Protect a window or balcony from intruders without hindering your view of the outdoors by installing an Invisible Grille Price, often known as stainless steel cables.
To prevent individuals from falling through an opening (like a balcony), the IVG system encloses it with stainless steel cables. It is a common fixture in Singapore’s high-rise HDBs, condos, and even workplaces.
While traditional grilles might be bulky and overpowering, invisible grilles are nearly imperceptible from a distance. They don’t get in the way of ventilation or views, and they don’t alter the look of the interior design.
Invisible Balcony Grille That Cannot Be Removed
Below is a list of what makes up an invisible grille:
Cable
Because it stops people and pets (like cats) from falling through the floor vents, this is the most crucial component of an IVG.
Depending on the type of cable, you should leave between two and four inches of space between them. There is usually no need for a wider range of height than three or four inches for very young children. Carpets usually sit at a conventional height of 2 inches in households with pets like cats.
A membrane, a thin coating of translucent plastic that protects the cable from the environment. Although nylon and Teflon are the most commonly used materials for the membrane, any of the plastics available today might be used.
Grasper for cables (Top & Bottom)
This is located at both the top and bottom of the installation site and is responsible for keeping the cables taut (e.g. Service Yard). The screws help reinforce the cable holding it in place. A shield will be set up over it to keep it out of sight and prevent any accidents from happening.
Please note that the complete installation will not rely on a single cable. Typically, only three-quarters of a gripper of this type will allow a continuous cable to pass through.
Stiffeners
These wires run across your major IVG wires to distribute tension evenly and limit the slack that can be created if two cables are pulled in opposite directions. These two characteristics help make the IVG system safer for use.
Invisible Grilles Come in a Variety of Types
Invisible Grille Price Singapore that is permanently installed Invisible grilles are most commonly installed in this fashion. The most common application for invisible grilles is as a permanent fixture, such as in the form of a grille or panel. This installation method is not limited to balcony railings; it may also be used on stair railings, window railings, and stairway railings.
A permanent framework is included in this, and it will be used to conceal grilles from view. They will protrude from the surface because they are installed on top of the existing window frame (around 5cm).
The design of an openable grille allows the window to be opened to the left or right, much like a standard window, with no restrictions. This design is constructed in a way that makes it possible for this design to exist.
Sliding Invisible Grille – This style of casement does not swing open to the left or right, but rather glides to either side. The sliding track requires multiple outwardly extending sections of wall (around 15cm).
The grille is made with a bi-folding method, where the casement is folded not once but twice to provide the desired effect. For easier window access, this can be folded to the slide.
Cable
Because it stops people and pets (like cats) from falling through the floor vents, this is the most crucial component of an IVG.
Depending on the type of cable, you should leave between two and four inches of space between them. There is usually no need for a wider range of height than three or four inches for very young children. Carpets usually sit at a conventional height of 2 inches in households with pets like cats.
A membrane, a thin coating of translucent plastic that protects the cable from the environment. Although nylon and Teflon are the most commonly used materials for the membrane, any of the plastics available today might be used.
Grasper for cables (Top & Bottom)
This is located at both the top and bottom of the installation site and is responsible for keeping the cables taut (e.g. Service Yard). The screws help reinforce the cable holding it in place. A shield will be set up over it to keep it out of sight and prevent any accidents from happening.
Please note that the complete installation will not rely on a single cable. Typically, only three-quarters of a gripper of this type will allow a continuous cable to pass through.
Read More: click